Air Compressor Repair
Breakdown diagnosis and repair on rotary screw and reciprocating compressors, 24 hours a day, on your floor.
Read more
Service
Air compressor service, repair and installation
Compressed air is the utility nobody notices until it stops. We keep rotary screw and reciprocating systems running across three states. When one goes down at 2am, a technician picks up the phone.
Overview
Air Compressor Systems
BM Industrial Solutions services every major compressor platform on the market: Gardner Denver, Sullair, Ingersoll Rand, Kaeser, Atlas Copco, CompAir/LeRoi, Quincy, Champion, Curtis and Saylor-Beall. We hold no factory dealership, so the recommendation you get answers to your application and nothing else.
Most of the calls we take turn out to be dryer problems, drain problems, filtration problems or piping problems that surface at the compressor. We diagnose the whole system, so the fix holds.
What we handle
- Rotary screw service. Oil and separator changes, air/oil filters, coolers, bearings, airend inspection and rebuild, VSD drive troubleshooting.
- Reciprocating service. Valve service, rings and gaskets, unloaders, pressure switches, belt drives and pump rebuilds.
- Air treatment. Refrigerated and desiccant dryer service, coalescing and particulate filtration, condensate drains and oil-water separators.
- Controls and monitoring. Pressure and load-hour troubleshooting, sequencing between multiple units, alarm and shutdown diagnosis.
- System installation. Sizing, foundations, electrical coordination, receiver tanks and complete air distribution piping.
- Emergency response. 24/7 breakdown coverage, including temporary air where production cannot wait for a repair.
Right-sized systems
Sized to the air your plant actually uses
An oversized compressor short-cycles, wastes energy and wears out early. An undersized one starves your tools and never unloads.
We measure actual demand before we quote anything: running pressure, pressure drop across the system, load and unload behaviour, and where your air is genuinely being consumed. Sometimes the answer is a smaller compressor and better piping. We will tell you when that is the case.
Whole-system diagnosis
We work back to what caused it
High discharge temperature, water in the lines, pressure that will not hold, a unit that trips on overload. These are symptoms with several possible causes. We work through the system methodically until the evidence points somewhere.
- Water at the tool usually traces back to the dryer or a failed drain.
- Pressure complaints at the far end of a plant usually come down to piping.
- Repeat overload trips often trace to the airend, cooler or supply voltage.
In detail
Break it down further
If you already know what the job is, go straight to the specifics.
We service every major compressor platform
- Gardner Denver
- Sullair
- Ingersoll Rand
- Kaeser
- Atlas Copco
- CompAir / LeRoi
- Quincy
- Champion
- Curtis
- Saylor-Beall
Recent work
From the field
A sample of installations and service work across South Carolina, Georgia and North Carolina.
24/7 emergency service
When it fails at 2am, you still get a technician
Breakdowns do not respect business hours. Our emergency line runs 24 hours a day, seven days a week. You reach someone who can diagnose the problem and dispatch a technician.
Questions
About air compressor systems
How quickly can you get to a compressor that is down?
We run 24/7 emergency coverage across South Carolina, Georgia and North Carolina. Response time depends on where you are and what the failure is. Call 843-401-9670 and we will give you a straight answer about arrival time.
Do you only work on certain brands?
No. We service Gardner Denver, Sullair, Ingersoll Rand, Kaeser, Atlas Copco, CompAir/LeRoi, Quincy, Champion, Curtis and Saylor-Beall, plus most other platforms you are likely to have. We are independent, so we are not steering you toward one manufacturer.
How often should a rotary screw compressor be serviced?
Interval depends on run hours, ambient conditions and the lubricant in use, but most units need attention at set hour intervals for oil, separators and filters, with a fuller inspection annually. Dusty or hot environments shorten that considerably. We set the interval from your actual run hours and adjust it as the unit tells us more.
Can you install a new system as well as repair the one we have?
Yes. Full installations including compressor, dryer, receiver, filtration and the distribution piping that connects it all. We handle the mechanical scope and coordinate with your electrician, or bring one in.
Is it worth repairing an older compressor?
Often, yes. A well-built reciprocating unit or an older rotary screw with a sound airend can be worth rebuilding. We will give you the honest comparison between repair cost, expected remaining life and the energy cost of continuing to run it.
One vendor
Other services
Most of our customers started with one of these and consolidated the rest. Fewer vendors, fewer handoffs, one number when something breaks.
Hydraulics
Cylinder, pump and hose repair for production equipment and heavy machinery, in the plant or in the field.
Explore
Mechanical Contracting
Equipment installation, relocation, rigging and mechanical repair. The work that gets machinery in place and running.
Explore
Process Piping
Compressed air, water and industrial process lines, fabricated and installed so pressure gets where it is needed.
Explore
Ready when you are
Get a quote for air compressor systems
Tell us the equipment, the symptom and how urgent it is. We will come back with a straight answer. If it is down right now, call instead.